Automatische Papierzuführmaschine mit Rotorkeilschlitz
Basisinformation
Modell: ND-LSI-2WB
Produktbeschreibung
Diese automatische Rotor-Keil-Slot-Papier-Einlegemaschine ist mit einem Touchscreen ausgestattet. Alle zugehörigen Parameter können angezeigt und angezeigt werden. Das Keilmaterial und die Abmessung können den Anforderungen des Kunden entsprechen. Wir bieten auch design service. Diese Maschine ist einfach zu bedienen und passt durch Werkzeugwechsel zu verschiedenen Ankertypen.
Technische Parameter
Outside Dimension |
910*880*1300(L*W*H)mm |
Equipment Weight |
250 Kg |
Motor Power |
0.75 Kw |
Work Voltage |
380 VAC |
Work Air Pressure |
0.4-0.6 hMp |
Manufacturing Product |
Motor Rotor Insulated Paper |
Rotor O.D. Range |
φ20-φ55 |
Length of Insulation Paper |
15-60 mm Adjustable |
(MAX) Width of wedge |
25 mm |
Rotor Slot number |
8-24 slots |
Work procedure |
Feeding-install fixture-plug in discharge |
Fixture |
Pneumatic Mechanical Fixture |
Feeding form |
Automatic |
Lubricant form |
Grease lubrication |
Vorbereitung vor der Ratenzahlung
Stellen Sie sicher, dass der Platz für den Gerätebetrieb mit den Abmessungen 2330X1550X1450 (einschließlich der Einzugsführung) ausreicht.
Der Ratenboden sollte fest und flach genug sein.
Die Stromversorgung ist Wechselstrom 380V und der Luftdruck ist 0.4 ~ 0.6Mpa;
Stützmatte installieren: Stellen Sie das Gerät an die gewünschte Stelle und stellen Sie die Höhe der vier Stützmatten auf 100 mm ein, bis keine Vibrationen mehr auftreten. Ziehen Sie dann die Schraube der Stützmatte fest.
Überprüfen Sie, ob die Übertragungsteile, die Sicherungsschraube und das Kabel im Leistungsregler lose sind oder nicht.
Störungen und Fehlersuche
Malfunction |
Check |
A.Equipment not run even press start button
|
n Power and air supply |
n Make sure all input signal from sensor are correct, travel switch (X10) is pressed, no signal from counter sensor (X2), push bar protector (X7) and no paper sensor(x6) and full feeding (X4). Also, there is signal from the mechanic hand (X0) and magnetic sensor (X1) of small cylinder. |
|
n Brake is power off or not |
|
n The feeding sensor(X3) should have signal if there is rotor on the guide way. |
|
n Check cylinder and air pipe, make sure the pressure is between 0.4 and 0.6MPa |
|
B. Fail to feed paper |
n Check whether the paper is jammed in the feeding or discharging part, whether the upper press wheel is down pressed |
C. No action or improper action in big cylinder |
n Make sure the air pressure is 0.4 -0.6MPa |
n Check whether the magnetic valve is functional. |
|
n Adjust the release valve of feeding cylinder to 0.3 Mpa |
|
D. Incorrect work indexing |
n Adjust indexing screw |
E. No action in small cylinder |
n Check whether the mechanical valve is down pressed. |
F. The position is not correct after reset |
n Adjust the counter sensor screw and make sure it is on the right position after reset. |
G. Paper jam
|
n If it was blocked in the forming tooling, the equipment would stop because of the protective switch on duty. If it was blocked behind the upper press wheel, press the stop button, now the mechanical hand still hold the rotors, press the single/automatic button to adjust it to manual, the mechanical hand will release the rotor, then take out the paper, and reset, adjust the button to automatic, and start the equipment. |
Produktgruppe : Anker-Fertigungsmaschine > Keil Einsteckmaschine